 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D200ED Series Very Low Cost, 2W SIP Dual Isolated Output DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: * 2W Output Power * Miniature SIP Case * UL Approved (File E245422) * Dual Isolated Outputs * 1,000 VDC Isolation * >3.5 MHour MTBF * 12 Standard Models * Industry Standard Pin-Out * LOWEST COST!! Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Units VDC Internal Capacitor A Units % % 150 250 0.02 mV P - P mV P - P % 0.01 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 1,000 60 70 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC VDC M pF kHz Units C C %/C Output Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple (20 MHz) Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit For Vin Change of 1% Iout = 10% to 100% See Note 2 See Note 2 120 Conditions Min. Typ. 3.0 1.2 15.0 75 150 Max. General RoHS Compliant Parameter Isolation Voltage, Input/Output Isolation Voltage, Output/Output Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Case Size Case Material Weight MicroPower Direct Physical 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com 0.77 x 0.28 x 0.39 Inches (19.6 x 7.0 x 10.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.09 Oz (2.8g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 3.5 Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 C mW VDC Typ. Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201ED D202ED D203ED D204ED D211ED D212ED D213ED D214ED D221ED D222ED D223ED D224ED Input Voltage (VDC) Nominal Range Output 1 Current (mA) Voltage (VDC) Output 2 Current (mA, Min) Current (mA, Max) Voltage (VDC) Current (mA, Max) Current (mA, Min) Efficiency (%, Typ) 80 82 82 83 80 83 85 83 81 82 84 84 Full-Load No-Load Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 500 500 500 500 250 250 250 250 5 5 5 5 12 12 12 12 24 24 24 24 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 500 487 487 481 208 201 196 201 102 101 99 99 30 30 30 30 12 12 12 12 7 7 7 7 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 200.0 112.0 83.0 67.0 200.0 112.0 83.0 67.0 200.0 112.0 83.0 67.0 20.0 12.0 9.0 7.0 20.0 12.0 9.0 7.0 20.0 12.0 9.0 7.0 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 200.0 112.0 83.0 67.0 200.0 112.0 83.0 67.0 200.0 112.0 83.0 67.0 20.0 12.0 9.0 7.0 20.0 12.0 9.0 7.0 20.0 12.0 9.0 7.0 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx approx 1 F to 10 F) be placed from each output to common. 3. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 4. These converters are specified for operation without external components. However, in some applications the addition of input/ouput capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Block Diagram Vin 5 VDC 12 VDC 24 VDC Input Capacitor 4.7 F 2.2 F 1.0 F Vout 5 VDC 9 VDC 12 VDC 15 VDC Output Capacitor 4.7 F 2.2 F 1.0 F 0.47 F For applications requiring very low output noise levels, a simple LC filter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve g Mechanical Dimensions Pin Connections Pin 1 2 4 5 6 7 Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) * Pin 1 is marked by a "dot" or indentation on the side of the unit Function +Vin -Vin -Vout 1 +Vout 1 -Vout 2 +Vout 2 MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of D214ED
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |